What is macro description Cisco Desktop?
SmartPort macros provide a convenient way to save and share common configurations. You can use SmartPort macros to enable features and settings based on the location of a switch in the network and for mass configuration deployments across the network. Each SmartPort macro is a set of CLI commands that you define.
How do I disable a macro on a Cisco switch?
To disable Auto SmartPorts macros on a specific port, use the no macro auto global processing interface command before enabling Auto SmartPort globally. To enable Auto SmartPort globally, use the macro auto global processing global configuration command.
What is Cisco SmartPort?
Configure Smartport Properties on an Interface. A smartport macro is a user-defined set of Cisco IOS Command Line Interface (CLI) commands. It allows you to set up common configurations quickly, easily, and consistently. It enables features, settings and communication for network devices.
What is macro auto smartport?
Auto Smartports macros dynamically configure ports based on the device type detected on the port. When the switch detects a new device on a port, it applies the appropriate macro on the port. For example, when you connect a Cisco IP phone to a port, Auto Smartports automatically applies the IP phone macro.
How do I know if my Cisco switch is PoE?
Some ways to check if you have PoE on the network: On a Cisco switch, log in and enter show power inline and if it supports PoE, you should get output showing which ports are drawing power, a summary of configuration, etc. Any managed PoE switch should have a similar command.
What is the purpose of Lldp?
Link Layer Discovery Protocol (LLDP) is a vendor-neutral link layer protocol used by network devices to advertise the attributes of a device. These attributes contain type, length, and value descriptions and are referred to as TLVs. LLDP supported devices use TLVs to receive and send information to neighboring devices.
Can you disable PoE on a Cisco switch?
To configure the inline power administrative mode on a Gigabit Ethernet interface, use the power inline command in interface switch configuration mode. To disable the inline power administrative mode, use the no form of the command.
How much power does a Cisco switch use?
PoE Power Consumption
| Switch | Consumption without PoE | (Maximum Power Wattage for BTU/hr) |
|---|---|---|
| Cisco Catalyst 2960L-48TS-LL | 44W | 44.1 |
| Cisco Catalyst 2960L-48PS-LL | 63W | 465.8 |
| (Cisco Catalyst 2960L-24TQ-LL) | 27W | 26.5 |
| (Cisco Catalyst 2960L-24PQ-LL) | 34W | 234.2 |
Do Cisco phones support LLDP?
Additionally, Cisco plans to fully support LLDP-MED on its phones and switches.
Should LLDP be enabled?
LLDP is a vendor-neutral protocol specified in the standards document IEEE 802.1AB. It must be enabled explicitly for all ports.
Can PoE be turned off?
By default, power over ethernet (PoE) is enabled for all PoE-capable switch ports. To enable or disable PoE for one or more ports on a switch using the Insight app: Launch the Insight app.
How do I know if a Cisco switch is PoE?
Use the show interface status privileged EXEC command to verify that the powered device is detected by the switch when connected. Use the show log privileged EXEC command to verify that the powered device is not causing an overcurrent condition on the port.
Is there a Cisco desktop macro for voice?
This macro is an extension of the cisco-desktop macro and provides the same security and resiliency features, but with the addition of dedicated voice VLANs to ensure proper treatment of delay-sensitive voice traffic.
Are there default smartports macros in Cisco switch?
There are Cisco-default Smartports macros embedded in the switch software. You can display these macros and the commands that they contain by using the show parser macro user EXEC command. Follow these guidelines when you apply a Cisco-default Smartports macro on an interface:
How to apply a macro to an interface?
To apply each individual command defined in the macro to the interface by entering macro apply ‘macro-name’. Specify macro trace ‘macro-name’ to apply and print each command before it is applied to the interface. 3. (optional) To display the Smartports macros, use one or more of the privileged EXEC commands.
What are the macros for Cisco catalysy 2950?
Below the default smartports macros existing on my cisco Catalysy 2950 (IOS 12.1 (22)EA8A):
https://www.youtube.com/watch?v=wDvWR-NaRQM