Categories :

How do I reset my Cisco E2500 router password?

How do I reset my Cisco E2500 router password?

Here’s how:

  1. Make sure the router is plugged in and powered on.
  2. Physically turn the E2500 over so you have full access to the bottom side.
  3. Using a small, sharp object such as a straightened paperclip, press and hold the Reset button for 10 seconds.
  4. Unplug the power cable for 10 to 15 seconds and then plug it back in.

How do I reset Linksys router to factory settings?

Locate the Reset button and, using a pen or a paper clip, press and hold the Reset button for 10 seconds. QUICK TIP: For router models such as the Linksys Wireless-B and Wireless-G routers, press and hold the Reset button for 30 seconds. QUICK TIP: Observe the Power light of the router while pressing the button.

How do I access my Linksys E2500 router settings?

For the Linksys E2500, you have to do the following steps for access:

  1. Put router into operation.
  2. Connect the device via Wi-Fi* or a network cable with the router.
  3. Open web browser.
  4. Insert IP address in the address bar and confirm with ‘Enter’ button.
  5. Enter username and password in the open user interface and confirm again.

How do I configure my Cisco Linksys router?

Instructions

  1. Visit the router’s IP address in a new browser window. http://192.168.1.1 is the default Linksys router IP address.
  2. Enter the Network password. The “Enter Network Password” window will appear.
  3. Type in OpenDNS addresses in Static DNS 1 and Static DNS 2 fields.
  4. Click Save Settings button.

How do I configure my Cisco Linksys E900 router?

To reset the Linksys E900 to its default settings, you have to do the following steps:

  1. Switch on router.
  2. Press Reset button and hold for at least 10 seconds.
  3. Device restarts automatically.
  4. Router has been reset to factory settings.

How do you reset your router to factory settings?

How to reset your router to restore factory default settings

  1. Locate the Reset button on the back of your router.
  2. With the router powered on, use the pointed end of a paperclip or similar object to press and hold the Reset button for 15 seconds.
  3. Wait for the router to fully reset and power back on.

What happens if you factory reset your router?

A reset restores your modem to its factory default settings. It will also erase any customized settings you may have changed, including static IP address setup, DNS, personalized password, WiFi settings, routing and DHCP settings.

How do I Reset my Linksys E2500 to factory defaults?

There are two (2) ways in resetting the Linksys E2500 to factory defaults: Press and hold the Reset button at the bottom of your router for 10 seconds then release. Log in to the router’s web-based setup page then go to Administration > Factory Defaults > Restore Factory Defaults. For more instructions on resetting your device, click here.

What is the default wireless network name ( SSID ) of Linksys E2500?

What is the default wireless network name (SSID) of Linksys E2500? The default wireless network name of Linksys E2500 is Linksysxxxxx. NOTE: The xxxxx is the last five (5) digits of the serial number of the router. You have to upgrade your firmware to have Linksysxxxx as the default SSID.

Where is the reset button on a Linksys router?

The Reset button is located at the bottom of the router. The LEDs and Wi-Fi Protected Setup™ (WPS) button are at the back of the router. 5. How many USB ports does the Linksys E2500 v3 have? The Linksys E2500 v3 has one (1) 2.0 USB port. 1. How do I install the Linksys E2500 router? The Linksys E2500 router can be installed in different ways.

Can you connect a printer to a Linksys E2500?

You can connect a printer to the Linksys E2500 using Linksys Connect. To learn how to connect a wireless printer, click here. To learn how to connect a USB printer, click here. NOTE: You can only connect a USB printer using Linksys Connect on the Linksys E2500 v3.